Sewage Ejector Pump

Sewage ejector pumps are an essential and often overlooked part of a septic system. If your sewage ejector pump is not working properly it can lead to major issues that could cost thousands of dollars in repairs or replacement.

In this article, we will discuss what a sewage ejector pump is, when you should replace it, how to install a new one, and how to maintain and troubleshoot your current pump. We will also answer some of the most common questions about sewage ejector pumps. Keep reading to find out more. 

What is a sewage ejector pump?

A sewage ejector pump is a centrifugal pump that is generally used in septic systems but can also be found in household waste disposals.

Image Credit: http://rooterman.com

It works by drawing water out of the septic tank and forcing it through the building drain system where it eventually leaves your home. Because of this, these pipes are usually located near or in the basement.

There are two main types of sewage ejector pumps – rotary vane pumps and diaphragm pumps. Rotary vane pumps are more common, but diaphragm pumps are quieter and can handle more solids.

When should you replace your sewage ejector pump?

The general rule of thumb is that you should replace your sewage ejector pump every 5-7 years. However, this may vary depending on the type of pump you have, how often it is used, and the condition of the septic system.

If you are not sure whether or not it is time for a replacement, there are a few telltale signs that can help you decide:

If the pump is making strange noises, vibrating, or leakingIf the pump smells bad or is creating an excessive amount of noiseIf the pump is not working properly or is constantly clogging

If you are experiencing any of these problems, it is time for a replacement. All of these issues can cause extensive damage to your septic system and can be very costly to repair.

How to install a new sewage ejector pump

Replacing a sewage ejector pump is not a difficult task, but you must take your time and follow the proper steps.

The first step is to shut off the power to the pump. You can do this by flipping the breaker switch or by unplugging the pump.

Next, remove the cover plate from the pump and disconnect any hoses or wires that are attached.

Then, use a screwdriver or wrench to loosen the bolts that hold the pump in place. Be careful not to damage them as they will need to be reused later.

After you have loosened the bolts, lift the pump out of its cradle and attach it to your new sewage ejector pump. Make sure that the wires are also facing the correct way before you tighten any nuts or bolts.

Once everything is secure, reattach all hoses and wires and replace your cover plate.

Finally, turn on your power supply and test out your new sewage ejector pump. If everything works properly, then you’re done. If not, don’t worry- there are plenty of troubleshooting tips for this later in the article. 

You can also check out this article onhow to install sump pumps if you’d like to know more about similar installation processes.

Sump Pump Cost: Average Prices, Installation – Forbes Advisor

Image Credit: http://forbes.com

How to maintain and troubleshoot a sewage ejector pump

While replacing an old sewage ejector pump can be relatively simple, maintaining it over its lifetime can be a bit more difficult.

There are a few things that you can do to help keep your pump running smoothly:

Clean the pump regularly and remove any debris or build-up that may have accumulated.Make sure that the seals and gaskets are in good condition and properly lubricated.Check the hoses for leaks or damage and replace them if necessary.If the pump starts to vibrate excessively, try adding additional insulation or baffles to quiet it down.

Troubleshooting tips 

If you are having problems with your sewage ejector pump, there are a few troubleshooting tips that you can try:

If the pump won’t turn on at all make sure that you have turned off and unplugged the pump and then check your circuit breaker.If the breaker is fine, try turning it on for 5-10 seconds before turning it back off again. Plug in the pump and see if it works properly.If this doesn’t work, there may be an issue with one of your wires or hoses. Check them out to make sure that they are connected properly or replace them accordingly. If they seem to be working fine, then there may be a problem with your electrical connections. Try tightening any loose wires/connections before calling a professional for help. If water is leaking from the pump check to see if the bolts are tight on the base of the pump. If they are, then there may be a problem with one of your hoses or wires.If these don’t seem to be the issue, try applying Teflon tape or pipe dopes to any threaded connections on your hoses and pipes. This will help seal any leaks that may have developed over time. If you can hear bubbles in your tank but you’re not getting any water out, the first thing that you should do is make sure that both valves are completely closed. Once this has been done, check for cracks or holes in any hoses or pumps leading into/out of the area around the tank.If everything seems to be in order, you may need to add more water to your tank. You can do this by opening up the valve and letting the water run until it is at the desired level. If this still doesn’t work, then you may have a blockage in your line and will need to call a professional for help. 

Hopefully, these tips will help you keep your sewage ejector pump running smoothly for years to come.

Sewage Ejector Pump – FAQ

What is a sewage ejector pump?

A sewage ejector pump is a pump used to remove wastewater from a building. The wastewater is typically removed from the lowest level of the building, such as a basement or crawlspace.

What are the benefits of using a sewage ejector pump?

The main benefit of using a sewage ejector pump is that it can help to prevent flooding. A sewage ejector pump can help to keep the wastewater in the building’splumbing system and out of the basement or crawlspace.

How do I know if I need a sewage ejector pump?

The best way to determine if you need a sewage ejector pump is to contact a professional plumber. They will be able to assess your building and determine if a sewage ejector pump is necessary.

How much does a sewage ejector pump cost?

The cost of a sewage ejector pump will vary depending on the size and type of pump you need. You can expect to pay anywhere from several hundred dollars to several thousand dollars for a quality sewage ejector pump.

How do I install a sewage ejector pump?

Installing a sewage ejector pump typically requires the help of a professional plumber. They will be able to help you install the pump and ensure that it is working properly.

Final thoughts on a sewage ejector pump

In conclusion, sewage ejector pumps are found in many different types of commercial and residential appliances. Though they may vary in size, the pump itself is relatively easy to maintain and repair when needed. 

These devices tend to last a very long time so you will probably not have to worry about replacing one for quite some time. If problems do arise, sewage ejector pump replacement can be done by most people with little technical experience.

The post Sewage Ejector Pump appeared first on Kitchen Infinity.

Did you miss our previous article…
https://www.healthycravingsholistickitchen.com/?p=961